i s o 9 0 0 1 product specification avx thin film operation itf series CP0603V0836CNTR specification revb page 1 of 3 high directivity, tight tolerance, lga termination directional coupler CP0603V0836CNTR itf technology the itf lga coupler is based on thin-film multilayer technology. the technology provides a miniature part with excellent high frequency performance and rugged construction for reliable automatic assembly. the itf coupler is offered in a variety of frequency bands compatible with various types of high frequency wireless systems. applications: ? mobile communications ? satellite tv receivers ? gps ? vehicle location systems ? wireless lan?s l and g rid a rray advantages: ? inherent low profile ? self alignment during reflow ? excellent solderability ? low parasitics ? better heat dissipation part number code: cp 0603 x xxxx x n tr type frequency sub- lga taped & (mhz) type term. reeled lead-free quality inspection : finished parts are 100% tested for electrical parameters and visual characteristics. each production lot is evaluated on a sample basis for: ? static humidity: 85 c, 85% rh, 160 hours ? endurance : 125 c, i r, 4 hours termination: nickel/ lead free solder coating (sn100) compatible with automatic soldering technologies: reflow, wave soldering, vapor phase and manual. dimensions - mm (inches) (bottom view) a t w l b s terminals ( top view) operating temperature: -40c to +85c l 1.60.1 (0.0630.004) a 0.360.05 (0.0140.002) w 0.840.1 (0.0330.004) b 0.200.05 (0.0080.002) t 0.600.1 (0.0240.004) s 0.0550.055 (0.0020.002) out in 50 ohm coupling
i s o 9 0 0 1 product specification directional coupler type CP0603V0836CNTR p/n frequency [ mhz ] coupling [ db ] i. loss [ db ] r. loss [db] directivity [db] CP0603V0836CNTR 836 -10.10.5 -0.7 max -21 typ 14.5 typ avx thin film operation itf series CP0603V0836CNTR specification revb page 2 of 3
i s o 9 0 0 1 product specification cp0402 / cp0603 high directivity couplers test jigs general description these jigs are designed for testing the cp0402 and cp0603 h igh directivity couplers using a vector network analyzer. they consist of a dielectr ic substrate, having 50 ? microstrips as conducting lines and a bottom ground plane located at a distance of 0.254mm from the microstrips. the substrate used is n eltec?s nh9338st0254c1bc. the connectors are sma type (female), ?johnson components inc.? product p/n: 142-0701-841. both a measurement jig and a calibration jig are provided. the calibration jig is designed for a full 2-port calibrat ion, and consists of an open line, short line and through line. load calibration can be done by a 50 ? sma termination. measurement procedure when measuring a component, it can be either soldered or pressed using a non-metallic stick until all four ports touch the appropriate pads. se t the vna to the relevant frequenc y band. connect the vna using a 10db attenuator on the jig terminal connected to port 2. follow the vna?s instruction manual and use the calibration jig to perform a full 2-port calibration in the required bandwidths. place the coupler on the measurement jig as follows: input (coupler) ? connector 1 (jig) termination (coupler) ? connector 3 (jig) coupling (coupler) ? connector 2 (jig) out (coupler) ? connector 4 (jig) to measure i.loss connect: connector1 (jig) ? port1 (vna) connector3 (jig) ? 50 ? connector2 (jig) ? 50 : connector4 (jig) ? port2 (vna) to measure r.loss and coupling connect: connector1 (jig) ? port1(vna) connector3 (jig) ? 50? connector2 (jig) ? port2 (vna) connector4 (jig) ? 50 ? to measure isolation connect: connector1 (jig) ? 50 ? connector3 (jig) ? 50 ? connector2 (jig) ? port2(vna) connector4 (jig) ? port1 (vna). measurement jig calibration jig short line to gnd. open line load & through load & through connector 1 connector 2 connector 4 connector 3 connector johnson p/n 142-0701-841 avx thin film operation itf series CP0603V0836CNTR specification revb page 3 of 3
|
